Friday, 22 December 2017

Acid-bathing metal

I'm not too big a fan of using (strong) acid to treat metal. Depending on its potency, it can be very hazardous (especially to skin and respiratory organ health), so it's definitely not for the clumsy. It's also much less controllable than using good old wire brush, file, and sandpaper. For rust-removal, non-acidic solutions do a fine job (see previous post).

That said, acid has notable benefits. It works rapidly and -- which is really the only reason I use it -- it eats away material in places that manual tools cannot reach. I had to derust the pipe in the picture below (part of my bike's engine-cooling system).


The engine-facing side was in especially bad condition because (whilst installed) it was virtually impossible to clean. Chrome gone, deeply entrenched rust everywhere. Manual tools did a good job cleaning it, but they did not reach underneath the welded-on attachment with the screw. Soaking in Evapo-Rust overnight worked well, but I still couldn't tell how clean the hidden area was. To ensure full removal of rust and any other deposits, I decided to use acid.

In NZ, hydrochloric acid (also called 'muriatic acid') is easily available. For example, Bunnings sells a Bondall product with 320g/L HCl, which makes it a ~28% acid solution by volume (currently ~$16 for 1L, regular price).


Hydrochloric acid isn't actually ideal for treating steel because the chemical reaction that takes place during immersion leaves the metal highly susceptible to rust-(re-)development. Phosphoric acid on the other hand does not, but unfortunately it's harder to obtain. DIY stores do not sell it at all (in NZ).

Preparation of a full set-up is key:
1) Get a plastic container for the acid bath (I went with 2L icecream). Do not use it indoors! The chemical reaction produces highly corrosive fumes that will damage your respiratory organs!
2) Ensure access to fresh water (hose or bucket) to be able to rinse the acid off the metal.
3) Prepare another container with alkaline solution. You'll need it to immerse the metal and actually neutralise the acid. Mix 1 part baking soda and 10 parts water.
4) Use rubber gloves, eye protection, and skin cover. If possible, set a timer. And, again, do not use the acid indoors.

NOTE: If you need to dilute an acid, remember the saying "do like you oughta, add acid to water". Otherwise, the exothermic reaction can be violent.

For my own project, I prepared the pipe by taping off both ends to prevent the acid from damaging the inside (which was pristine). Rubber from old gloves and masking tape (very firmly tied around) did a great job sealing the openings, nothing got in. Having moved the entire set-up to the deck, I placed the pipe in the ice cream container (screw pointing up) and poured the acid, just enough to get in under the attachment without touching the threaded part. The metal began to throw bubbles almost immediately, a bit like strongly carbonated mineral water. Checking every 5 minutes, a quarter hour turned out to be enough. The pipe looked like it was covered in zinc, underneath the attachment too. A good water rinse, then immersion in alkaline solution. Bubbles (indicating that neutralisation is ongoing) ceased after a few minutes. Another water rinse, and that was that.

The metal surface began to develop flash-rust after only about 20-30 minutes, so HCl really isn't ideal. Fortunately, that issue can be addressed quite easily: dump the part in Evapo-Rust (and leave it in till you're ready to process it).

As for storing the acid for future use, pour it back in the original bottle. That said, don't mix used and virgin acid. (I use glass jars.) Make sure you label everything. If you have kids, store the containers out of reach.

Thursday, 21 December 2017

Derusting bike parts

I tend to wield wire brush, file, and sandpaper to derust parts (at least if I don't care about preserving chromed surface and the likes), but I often combine it with the use of non-acid*, liquid rust-remover. It's slower, but it's undeniably convenient. Also, it reaches places where manual tools cannot go and it prevents rust from re-occurring (eg, if you don't have time to further process parts right away). In a way, using it as a supplement gives peace of mind because it dissolves any rust that manual labour may have missed.

Unsure which product to use, I decided to try Evapo-Rust, and I've been mightily impressed by its effectiveness. Soak parts overnight, have rust-free pieces in the morning, almost magical.


In New Zealand you can get it at Supercheap Auto (currently $30 for 1L, regular price). Pour it in a plastic icecream container (with lid), use it over and over. It starts out light yellow and turns darker over time, presumably because it absorbs the rust. (If you manually remove as much rust as possible from parts beforehand, the liquid goes a long way.)


The solution and the soaked parts can be handled without gloves, it does not seem to affect skin at all. There are no fumes either, way safer than acid baths. Also, you can soak the parts for however long you like. 'Healthy' metal and chrome remain untouched (so it's safer in that regard too).

Here's a tip for using Evapo-Rust on parts that, for whatever reason, cannot be immersed in a container: use a paintbrush to apply the solution to the part's surface and cover it with glad-wrap (trap as little air as possible between metal and film). Preventing evaporation, the cover ensures prolonged exposure to the liquid. I used this method to treat my shocks (too large for the container), very effective. If the solution dries in places, it may leave a brownish residue which can be removed with a wire brush (or Brakleen and a cloth).


- - -
* I'll write about acid use and metal etching in another post.

Wednesday, 20 December 2017

Hi ho

I've been riding motorcycles since turning 16, and my current bike -- a 1992 Honda CB1000 (Big One) -- since 2011. For riders who are happy without the fancy technology of modern bikes, who want a reliable engine that runs forever, and who prefer something that's a bit heftier (and suitable for the tall-ish), the old CB1000 is a pretty sweet machine. I would not hesitate to recommend it.


That said, a 1992 bike needs the occasional repair, it's been a quarter-century since gestation after all. I'm a firm believer in DIY, for various reasons: it builds/maintains a useful skill set, it represents a kind of bodily performance that office jobs lack, and -- perhaps most importantly -- it turns the vehicle into a meaningful object. Modern (Western) consumers are alienated from most of their possessions because they have little or no involvement in their making, their maintenance, their recycling, etc. Lack of involvement means lack of relationship with the object. Taking care of an item imbues it with significance because the user invests it with a number of scarce personal resources (eg, attention, labour, and time). DIY builds strong object-person relations, and in the context of throw-away consumerism that's a good thing.*

I'll use this blog to publish various notes on my own bike repair jobs -- what worked, what didn't, how well it turned out. I would have liked to find such notes when I needed them myself, they would have saved me significant effort, time, and money. I hope my comments benefit others in turn.

Since I write from New Zealand, some of the brands/products I mention will mean little to non-kiwis. That said, you should be able to find corresponding items in your own country.

Sensible/useful comments and questions are very welcome, of course.

Cheers & ride well,
M.


- - -
* I'm PhD-ing on this topic, so I have distinct views about it.